Gas Valves & Conversion Kits

Voomi Supply carries gas valves and natural gas to propane conversion kits from leading manufacturers, in millivolt, intermittent pilot and 24V types across single-stage and two-stage designs. A gas valve opens, closes and regulates the fuel feeding a furnace, boiler or water heater burner, and a conversion kit swaps the orifices and regulator spring so the appliance can run on the other fuel. Every order ships with Voomi's 30-day return policy and free help matching a valve or kit to your appliance.

Customer Support Image
Need Support?

Call Jack and His Team

Gas Valve Types at a Glance

Type

How it works

Where it is typically found

Example

Millivolt (standing pilot)

A thermocouple or thermopile powers the valve from the pilot flame, so no line power is needed

Older furnaces, gas water heaters, wall heaters

Robertshaw 700-515

Intermittent pilot

A 24V valve with separate pilot and main coils; a spark lights the pilot on each call for heat and the main valve opens only after the pilot flame is proven

Furnaces and boilers with electronic ignition

Honeywell SV9601M4571

Direct spark or hot surface ignition

A 24V valve opens for a short trial for ignition, then a flame sensor must prove the flame

Most modern furnaces

Honeywell VR8215T1502

Single-stage

On or off, one firing rate

Basic furnaces and boilers

Carrier EF32CW151 (24V, 3.5 in. WC)

Two-stage

Low fire at roughly 60 to 70% of capacity and high fire at 100%

Two-stage furnaces

White-Rodgers B1282620 Two Stage D.S.I. Gas Valve Furnace

Modulating

Stepper motor or PWM actuator varies the firing rate

High-efficiency modulating furnaces

HONEYWELL VS820A1740 Low-Pressure Modulating Gas Valve

Typical Gas Pressures

These are typical ranges from an HVAC training reference. The appliance data plate and manufacturer instructions always take priority.

Measurement (inches water column)

Natural gas

Propane (LP)

Inlet pressure

5 to 7

11 to 13

Single-stage or high fire manifold

3.5

10.0 to 11.0

Two-stage low fire manifold

1.5 to 1.9

4.5 to 5.0

What a Conversion Kit Contains

Kit contents vary by appliance. As one example, a Trane furnace LP kit lists main burner orifices, a replacement spring for the first-stage regulator, a pressure tap adapter, an installer guide and warning labels. Always use the kit made for the exact furnace, boiler or water heater model. Kits on this page include the Goodman LPM-06 for two-stage furnaces and the Carrier KGAPN3901ALL for converting LP to natural gas.

How to Match a Valve or Kit

Check

Why it matters

Appliance model and valve part number

Both are printed on the data plate or valve body; valves are model specific

Control voltage

Millivolt, 24V and 120V valves are not interchangeable

Inlet and outlet pipe size

Fittings must match the gas line and manifold

Fuel type and pressure

Natural gas and propane use different orifices and regulator settings

Ignition system

Standing pilot, intermittent pilot and direct ignition valves are wired differently

Gas Valve Terms Explained

Term

What it means

Combination valve

One body that holds the manual shutoff, two safety shutoff seats in series, the pressure regulator and the main operator

Inlet and outlet size

Pipe size at each port, written as inlet x outlet such as 3/4 x 3/4 or 1/2 x 1/2

Pressure regulator

Holds the manifold pressure at the value on the appliance data plate; its spring is what a conversion kit changes

Safety shutoff

Redundant seats that close if the flame is lost or the control drops the call for heat

Pilot and main coils

Intermittent pilot valves have a pilot coil that opens first and a main coil that opens after the pilot flame is proven

Slow opening

Valve that opens the main seat gradually to give soft burner ignition

Gas Valve Troubleshooting Basics

These checks come from an HVAC service guide. Values vary by appliance, so confirm them against the manufacturer specifications, and only qualified technicians should test live gas equipment.

Check

What it tells you

24 to 28V AC between W and C during a call for heat (furnace)

Confirms the control board is sending power to the valve

No voltage at the valve

Points to the control board, a safety switch or wiring, not the valve

Coil resistance with power off and wires disconnected: about 40 to 70 ohms on a furnace, 40 to 80 ohms on a water heater

An open reading means a burned out coil and a zero reading means a short

Voltage present, good coil, no gas flow

Points to a seized valve body

Valve clicks but no gas flows

Regulator failure or a blocked inlet

Manifold pressure on a manometer: about 7 inches WC inlet and 3.5 inches WC outlet on a natural gas furnace

An out of range difference suggests a regulator problem; high pressure shortens igniter and heat exchanger life, low pressure causes ignition trouble

Water heater pilot will not stay lit after release

Replace the thermocouple first; if the valve still will not hold, replace the combination valve

When to Replace the Valve

A service guide lists these reasons to condemn a gas valve: gas leaking through the valve body and not just a fitting, the valve has been submerged, it is over 20 years old with visible degradation, a recall or service bulletin applies, or the body is physically damaged. A failed thermocouple or coil alone is not a reason to condemn the whole valve.

Gas Safety Basics

Situation

Safe practice

After any gas connection work

Run a full leak check with a listed combustible gas detector, use soap solution as a second check on fittings, and do it before restoring power or lighting the appliance

Shutting the gas off

Use the appliance shutoff first; use the meter shutoff only for a confirmed leak or when the appliance shutoff cannot be reached

Smell of gas

Avoid switches and ignition sources, shut off the supply if safe, leave the building if the odor is strong and call the gas utility from outside

Propane conversion

Propane collects in low areas, so a gas detector is recommended in basements and confined spaces

Related Parts

Valves are often replaced together with pilot assemblies or ignitors on the same appliance.

Frequently Asked Questions

Gas valves control the flow of gas to the furnace or other heating units in HVAC systems. They are essential for regulating the heating process safely and efficiently. Most valves combine a manual shutoff, two safety shutoff seats in series, a pressure regulator and the main operator in one body.

Conversion kits allow you to switch between different types of gas (e.g., from natural gas to propane) to ensure your HVAC system operates with the appropriate fuel type. Propane runs at a higher manifold pressure than natural gas, so the orifices and regulator spring are changed and the pressure is rechecked.

Start with the appliance model number and the valve part number on the data plate. Then confirm the control voltage, pipe size and fuel type. Replacement valves are listed by model, and an exact match is safer than a similar looking valve.

Valve internals are not serviceable. Only the pressure regulator setting is adjusted, and only to the values on the appliance data plate. A failed valve is replaced as a unit.

Check for 24 to 28V AC at the valve during a call for heat, then check coil resistance with the power off. Voltage with a good coil but no gas flow points to a seized valve, and no voltage points to the control board or wiring. A manometer on the test ports confirms inlet and manifold pressure.

A millivolt valve is powered by a thermopile at the pilot, so it works without line power. A 24V valve is switched by the thermostat and control board, and it is used with intermittent pilot, direct spark and hot surface ignition systems.

Many valves can be converted with the manufacturer kit by changing the regulator spring and the burner orifices, but not all can. Check the valve and appliance instructions for the approved kit and the manifold pressure for each fuel.

Replace it when gas leaks through the body, when it has been submerged, when the body is damaged or a recall applies, or when it is old with visible degradation. If only a thermocouple or coil failed, that part may be the only repair needed.

Installation should be done carefully, following the manufacturer's instructions. We recommend consulting a licensed HVAC technician to ensure proper installation and safe operation. Manufacturers state that a conversion must be done by a qualified service agency, because errors can cause fire, explosion or carbon monoxide. Propane is heavier than air and collects in low areas, so a gas detector is recommended in basements and confined spaces.