DAKOTA SOURCING

Product DescriptionThe DAKOTA SOURCING 13129 is a reducing coupling designed to transition between two different connection sizes in a single fitting. It features a 5/8-inch female iron pipe thread (FTF) on one end and a 1/2-inch outside diameter (OD) connection on the other. This...

Product DescriptionThe DAKOTA SOURCING 13107 is a coupling fitting with a 7/8-inch outer diameter. Couplings are used to join two sections of tubing or pipe in a straight run, maintaining flow continuity within a system. This single-unit fitting is suited for plumbing, refrigeration, or...

Product DescriptionThe DAKOTA SOURCING 13049 is a 45-degree elbow fitting sized at 7/8 inch OD. This fitting redirects tubing or pipe runs at a 45-degree angle, reducing stress on the line and allowing for cleaner routing in tight spaces. It is used in refrigeration,...

Product DescriptionThe DAKOTA SOURCING 13111 is a copper coupling designed to join two lengths of copper tubing with an outside diameter reduction from 3/8 inches to 1/4 inches. This fitting is a standard sweat-style reducer coupling used in refrigeration, HVAC, and plumbing applications where...

Product DescriptionThe DAKOTA SOURCING 13007 is a single elbow fitting sized at 1-1/8 inches OD. Elbow fittings redirect flow in a piping or tubing run, allowing installers to change direction without cutting or bending the line. This fitting is sold as a single unit...

Product DescriptionThe DAKOTA SOURCING 42538 is an 18-gauge hanging wire supplied in a 330-foot length. This wire is used to suspend HVAC equipment, ductwork, piping, signs, and other overhead installations where a reliable, lightweight support wire is required. The 18-gauge diameter provides a balance...

Product DescriptionThe DAKOTA SOURCING 13113 is a reducing coupling designed to connect tubing or piping of two different outside diameters. One end accepts 1/2-inch OD tubing and the other accepts 3/8-inch OD tubing, making it a straight-run reducer for systems where a diameter transition...

Product DescriptionThe DAKOTA SOURCING 18304 is a high performance pad designed as a single replacement unit for trade and service applications. Measuring 6 inches by 6 inches by 0.875 inches, this pad delivers consistent dimensional accuracy for a proper fit in supported equipment. Licensed...

Product DescriptionThe DAKOTA SOURCING 13131 is a reducing coupling designed to connect two refrigerant or fluid lines of different sizes within a plumbing or HVAC system. It features a 7/8-inch FTG (fitting) connection on one end and a 5/8-inch OD connection on the other,...

Product DescriptionThe DAKOTA SOURCING 12427 is a gas ball valve designed for gas piping systems requiring reliable manual shutoff. Featuring 3/4-inch female x female (FxF) threaded connections on both ends, this valve provides a quarter-turn shutoff mechanism suited for natural gas and LP gas...

Product DescriptionThe DAKOTA SOURCING 13001 is a 3/8-inch OD copper 90-degree elbow fitting used to redirect refrigerant or fluid lines at a right angle within mechanical systems. Fabricated from copper, this elbow provides a durable, corrosion-resistant connection point where tubing must change direction by...

Product DescriptionThe DAKOTA SOURCING 13128 is a reducing coupling designed to connect two tubing or pipe sections of different outside diameters. It transitions from a 5/8-inch OD connection to a 1/2-inch OD connection in a single fitting. Reducing couplings like this one are standard...

Product DescriptionThe DAKOTA SOURCING 13013 is a 90-degree long-radius copper elbow fitting with a 1/2-inch outer diameter and a 3/8-inch inner diameter, joined in a copper-to-copper (C x C) configuration. This fitting is used to redirect copper tubing runs at a 90-degree angle while...

Product Description The DAKOTA SOURCING 13318 is a copper P-trap designed for drain, waste, and vent (DWV) plumbing systems in residential and light commercial applications. The trap maintains a water seal in the drain line to block sewer gases from entering occupied spaces. It...

Product DescriptionThe DAKOTA SOURCING 18308 is a cork and rubber vibration isolation pad designed to reduce noise and vibration transfer between mechanical equipment and mounting surfaces. Measuring 4 inches x 4 inches x 7/8 inch, this pad fits under condensing units, compressors, pumps, and...

Product Description The DAKOTA SOURCING 13031 is a 90-degree copper street long elbow designed for sweat-connect copper plumbing systems. This fitting features a FTG (fitting, or street) end on one side and a cup-end socket (C) on the other, allowing it to connect directly...

Product Description The DAKOTA SOURCING 13317 is a copper P-trap designed to create the water seal that blocks sewer gases from entering a drain line. It fits into the drain assembly between the fixture tailpiece and the drain stub-out, maintaining a standing column of...

Product DescriptionThe DAKOTA SOURCING 13118 is a copper reducing coupling designed to connect two different-diameter copper tubing runs in a sweat-soldered (C x C) configuration. It transitions from a 7/8-inch OD (3/4-inch ID) tube on one end to a 3/4-inch OD (5/8-inch ID) tube...

Product DescriptionThe DAKOTA SOURCING 13005 is a 90-degree copper sweat elbow fitting designed for use in residential and light commercial plumbing and hydronic systems. With an outer diameter of 3/4 inches and an inner diameter of 5/8 inches, this C x C (copper-to-copper) fitting...

Product DescriptionThe DAKOTA SOURCING 13023 is a 90-degree copper street elbow designed for sweat-solder plumbing connections. It features a fitting-by-copper (FTG x C) end configuration, with a 3/4-inch outer diameter and a 5/8-inch inner diameter. This fitting directs flow at a right angle within...