HILLMAN

Product DescriptionThe HILLMAN 123117 is a 28-gauge galvanized steel general purpose wire sold in a 100-foot dispenser pack. Galvanized steel construction provides corrosion resistance for both indoor and outdoor use. The dispenser pack format allows controlled, tangle-free payout during use, which is practical on...

Product DescriptionThe HILLMAN 123130 is a 25-foot coil of 16-gauge galvanized steel general purpose wire, packaged in a convenient dispenser pack. Galvanized steel construction provides corrosion resistance for both indoor and outdoor use. At 16 gauge, the wire offers enough rigidity for securing, bundling,...

Product Description The HILLMAN 122537 is a brass plated trim nail designed for finish carpentry applications including hardwood molding and interior trim installation. Manufactured at 13 gauge with a 1-1/4 inch shank length, these nails provide secure, low-visibility fastening in hardwood and softwood trim...

Product DescriptionThe HILLMAN 122516 is a bright wire brad nail designed for fine finish and detail carpentry work. At 1-1/2 inches in length and 16 gauge in diameter, this nail features a small cupped head and slim shank that can be set below the...

Product DescriptionThe HILLMAN 560280 is a Phillips pan head self-drilling sheet metal screw designed to drill, tap, and fasten in a single operation. Sized at 8-18 x 1-1/2 inches, these screws eliminate the need for a separate pilot hole or tapping step, saving time...

Product Description The HILLMAN 47701 is a self-piercing pole barn screw designed to fasten thin sheet metal to wood, fiberglass, or metal substrates. The needle point tip drives without pre-drilling, and the hex washer head accepts standard hex drivers for fast installation. Each screw...

Product Description The HILLMAN 121030 is a zinc-plated steel picture hanger designed for straightforward installation on drywall and plaster surfaces. Each hanger ships with a nail included, eliminating the need to source separate fasteners. The 121030 is rated to hold up to 30 pounds,...

Product Description The HILLMAN 41400 is a blue conical plastic anchor designed for light-duty static fastening in masonry and wallboard substrates. Each anchor accepts a 6-8 thread screw and measures 3/4 inch in length. The conical design expands against the base material as the...

Product DescriptionThe HILLMAN 41554 is a slotted hex washer head concrete screw designed to fasten materials directly into concrete, brick, and block without anchors or inserts. The hardened high-low thread cuts its own path into masonry as the screw is driven, creating a secure...

Product DescriptionThe HILLMAN 375221 is a carbide-tipped masonry drill bit designed for use with Tapcon-style concrete anchors. It bores clean, accurate pilot holes into concrete, block, and brick, allowing Tapcon fasteners to thread in properly and hold with full rated strength. The 135-degree split-point...

Product DescriptionThe HILLMAN 122548 is a 3/4-inch, 18-gauge bright wire nail packaged in a 6-count, 2-ounce unit. The slim shank and small head profile allow the nail to seat with minimal surface disruption, making it a practical fastener for finish and trim work where...

Product Description The HILLMAN 122621 is a brass plated steel escutcheon pin designed for woodworking, craft, and decorative finish applications. Each pin features a smooth shank with a large half-round domed head that sits flush and adds a finished appearance wherever a small decorative...

Product Description The HILLMAN 122513 is a bright wire brad nail intended for fine, detail-level fastening in wood and trim work. At 1-1/4 inches in length and 16 gauge, it features a small cupped head and a slender diameter designed to be driven flush...

Product DescriptionThe HILLMAN 122594 is a blued cut tack designed for light-duty fastening applications in residential and commercial settings. Cut tacks are short, sharp-pointed fasteners with a relatively large flat head that drives flush or near-flush into soft substrates. The blued finish provides a...

Product Description The HILLMAN 123114 is a 30-foot coil of 19-gauge stainless steel general purpose wire packaged in a convenient dispenser pack. Stainless steel construction resists corrosion, making this wire suitable for both indoor and outdoor applications where moisture or chemical exposure is a...

Product Description The HILLMAN 5061 is a blue conical plastic anchor designed for light-duty static fastening applications where holding power is not the primary requirement. Each anchor accepts a 6-8 thread screw and measures 3/4 inches in length. The conical plastic body expands inside...

Product DescriptionThe HILLMAN 375223 is a carbide-tipped Tapcon masonry drill bit designed for drilling pilot holes in concrete, block, and other masonry materials. The 135-degree tip angle helps center the bit on contact and reduces walking at the start of the hole. At 3/16...

Product DescriptionThe HILLMAN 122689 is a 25-pack of large round brown leatheroid upholstery nails designed for decorative fastening applications where the nail head will remain visible. These tack nails feature an antique brass hammered finish that suits traditional and period-style furniture work. They are...

Product DescriptionThe HILLMAN 376648 is a size 8 nylon self-drilling drywall anchor sold in a 100-count box. The anchor drills its own hole directly into drywall without requiring a pre-drilled pilot hole, saving installation time compared to standard plastic anchors. The optimized thread profile...