AIR FLOW PRODUCTS

Product Description The AIR FLOW PRODUCTS EC18 is a tee end cap designed to terminate or close off the open end of an 18-inch tee fitting in a duct or pipe distribution system. It provides a clean, secure seal at the end of a...

Product DescriptionThe AIR FLOW PRODUCTS 189026 is an 18-inch, 90-degree sheet metal elbow fabricated in 26-gauge steel. It is a standard duct fitting used to redirect airflow at a right angle within forced-air HVAC duct systems. The 26-gauge construction provides a solid balance of...

Product DescriptionThe AIR FLOW PRODUCTS 5241408 is a straight ceiling diffuser boot designed to connect sheet metal ductwork to a ceiling diffuser or register in residential and light commercial HVAC systems. The boot transitions from the round or rectangular duct collar to the diffuser...

Product DescriptionThe AIR FLOW PRODUCTS RVG40010 is a roof cap designed to terminate ventilation ductwork at the roofline. It provides a weather-resistant exit point for exhaust airflow from HVAC, kitchen, bath, or general exhaust systems. The cap protects the duct opening from rain, wind,...

Product Description The AIR FLOW PRODUCTS DB425 is a metal dryer vent box designed for installation in 2x6 framed walls. It provides a recessed cavity behind the dryer, allowing the appliance to sit closer to the wall without crimping or crushing the exhaust duct....

Product DescriptionThe AIR FLOW PRODUCTS 77F142014 is a straight transition boot with flange designed to connect square or rectangular ductwork to a round collar in residential and light commercial HVAC systems. This fitting transitions a 14 x 20 inch rectangular opening down to a...

Product Description The AIR FLOW PRODUCTS RE2018 is a duct reducer-increaser fitting designed to transition between 20-inch and 18-inch round duct diameters in forced-air HVAC systems. This type of fitting allows ductwork installers to step down or step up airflow paths where duct sizing...

Product Description The AIR FLOW PRODUCTS 7731007 is a straight register boot designed to connect rectangular duct openings to floor, wall, or ceiling registers in residential and light commercial HVAC distribution systems. This boot transitions from a 3.25 by 10 inch rectangular duct opening...

Product DescriptionThe AIR FLOW PRODUCTS DP3036 is a metal drain pan sized at 30 inches by 36 inches, designed to catch condensate and prevent water damage beneath HVAC equipment. This type of secondary drain pan is commonly installed under air handlers, fan coils, and...

Product Description The AIR FLOW PRODUCTS 84AT06 is an airtight stick-on takeoff fitting designed for use with flat duct systems. It provides a branch connection point directly off the main flat duct run, using an adhesive-backed mounting method that eliminates the need for sheet...

Product Description The AIR FLOW PRODUCTS 77162018 is a straight transition boot with flange, designed to connect square or rectangular ductwork to round collar outlets in forced-air HVAC systems. Built to the 77F profile, it transitions from a 16x20 inch rectangular opening to an...

Product Description The AIR FLOW PRODUCTS 7741006 is a straight register boot designed to connect round duct to a rectangular floor, wall, or ceiling register in residential and light commercial HVAC systems. The boot features a 4x10 inch rectangular register opening and a 6...

Product Description The AIR FLOW PRODUCTS 7731006 is a straight register boot designed to connect rectangular duct openings to floor, wall, or ceiling registers in residential and light commercial HVAC systems. This boot features a 3.25 x 10 inch rectangular face opening and a...

Product DescriptionThe AIR FLOW PRODUCTS 7341206 is a 90-degree register boot designed to transition ductwork from a horizontal run to a vertical or wall-mounted register opening. This sheet metal fitting connects the supply duct to the register face, directing conditioned air into the living...

Product DescriptionThe AIR FLOW PRODUCTS FB03INS000212624 is a furnace filter box insulation panel designed to line the interior of a filter box housing in a forced-air heating or cooling system. It reduces heat loss, limits condensation on the box walls, and helps maintain system...

Product DescriptionThe AIR FLOW PRODUCTS 169026 is a 90-degree sheet metal elbow used in ducted HVAC air distribution systems. Fabricated from 26-gauge steel, this fitting redirects airflow at a right angle and is sized at 16 inches. It is a standard component in trunk-and-branch...

Product DescriptionThe AIR FLOW PRODUCTS 84DB06 is a 6-inch duct board tab takeoff fitting designed for use in low-pressure air distribution systems built with duct board (fiber glass duct board) construction. This fitting connects branch ducts to a main duct board trunk, maintaining a...

Product Description The AIR FLOW PRODUCTS MTD1008 is a metal duct conical spin-in takeoff fitting with an integral damper, sized at 10 inches by 8 inches. This fitting is used to branch conditioned air from a main trunk duct into a branch run, and...

Product DescriptionThe AIR FLOW PRODUCTS FB03INS000172624 is a furnace filter box insulation panel designed to line the interior of a filter box assembly in a forced-air heating or cooling system. Measuring 17.5 inches by 26.44 inches by 24 inches, this insulation fits within the...

Product Description The AIR FLOW PRODUCTS 59061408 is a short top insulated boot with flange, designed for use in residential and light commercial HVAC duct systems. This boot connects flex duct or rigid duct runs to floor, wall, or ceiling register openings. The 59F...