HAMMOND

Product Description The HAMMOND CWSC1036NK is a straight section used in wireway and cable management systems. Straight sections serve as the primary run component in surface-mounted raceway assemblies, providing a protected pathway for electrical conductors and control wiring. This section connects to compatible fittings,...

Product DescriptionThe HAMMOND PFK5 is a primary fuse kit designed to provide overcurrent protection on the primary side of low-voltage transformers commonly found in HVAC control circuits. Fuse kits of this type limit fault current before it can damage the transformer winding or downstream...

Product Description The HAMMOND 1481WN4SS1308 is a NEMA 4X window kit designed for use with compatible stainless steel enclosures. Window kits allow visibility into the interior of a sealed enclosure without opening the door, supporting status monitoring and indicator light visibility in washdown, wet,...

Product Description The HAMMOND CWSC1012NK is a straight section cable tray designed for organized routing and support of electrical cables and wiring in commercial and industrial installations. Straight sections form the backbone of a cable management system, providing a continuous, open pathway that keeps...

Product Description The HAMMOND PH75MGJ is a 75 VA control transformer designed to step down line voltage to low-voltage control circuit levels in HVAC, industrial, and commercial electrical systems. Control transformers of this type isolate and power relay logic, contactors, motor starters, and other...

Product Description The HAMMOND 1418H8 is a NEMA 12 rated wall mount enclosure designed to house and protect electrical components in industrial and commercial environments. NEMA 12 enclosures provide protection against dust, dirt, and dripping non-corrosive liquids, making this unit suitable for indoor industrial...

Product Description The HAMMOND CS10104 is a Type N1 screw cover designed for use with compatible Hammond enclosures. This cover provides a secure, tool-accessible closure for enclosure openings, helping maintain environmental protection ratings for the enclosure assembly. It is typically installed by electricians and...

Product Description The HAMMOND CWJO10 is a joiner and extra coupling fitting designed for use with wireway and cable management systems. It connects wireway sections end-to-end, maintaining a continuous, secure raceway path for conductors. Licensed electricians and electrical contractors install this type of fitting...

Product Description The HAMMOND CWSC636NK is a straight section component used in cable tray systems for organized wire and cable management in commercial and industrial electrical installations. Straight sections form the primary runs of a cable tray assembly, providing a rigid, open pathway that...

Product Description The HAMMOND VT57A is an open type transformer designed for use in control and low-voltage distribution circuits. Open type construction means the core and coil assembly is exposed, making it suitable for enclosure mounting in panels, control boxes, and equipment cabinets where...

Product Description The HAMMOND PH50MLI is an electrical enclosure manufactured by Hammond, a recognized name in protective housing solutions for electrical and electronic components. Designed to house and protect wiring, terminals, controls, or electronic assemblies, this enclosure provides a structured mounting environment suitable for...

Product Description The HAMMOND C3RWT412 is a Type 3R wiring trough designed to protect and route electrical conductors in outdoor and wet-location installations. Type 3R enclosures are rated to keep out rain, sleet, and external ice formation, making this trough suitable for exterior electrical...

Product Description The HAMMOND HP50 is a knockout hole plug designed to seal unused 0.5-inch conduit openings in electrical enclosures, junction boxes, and panel knockouts. It blocks dust, debris, and moisture from entering the enclosure through open knockouts left after conduit layout changes or...

Product Description The HAMMOND PH75MLI-FK is a 75 VA control transformer designed to step down line voltage to a lower control-circuit voltage in HVAC, industrial, and commercial electrical systems. Control transformers of this type are used to power low-voltage control circuits, relays, contactors, and...

Product Description The HAMMOND CWAD8 is a panel adapter designed to mount or convert an interior panel within an enclosure. Panel adapters of this type provide a secondary mounting surface inside electrical or control enclosures, allowing technicians to organize components, sub-panels, or DIN rail...

Product Description The HAMMOND PFA60000LG is a 13-inch exhaust filter designed to capture airborne particulates at enclosure exhaust points in electrical and industrial panel applications. It mounts at the exit point of a ventilated enclosure, trapping dust and debris before air leaves the cabinet....

Product Description The HAMMOND CWSC448NK is a straight cable tray section used in industrial and commercial electrical distribution systems to support and route electrical cables and conductors. This section provides a rigid, open-top pathway for cable management, keeping wiring organized and protected along horizontal...

Product Description The HAMMOND PH100PG-FK is a 100 VA control transformer designed to step down line voltage to a lower control-circuit voltage in HVAC, industrial, and commercial electrical systems. Control transformers isolate and power low-voltage control circuits, protecting sensitive components such as thermostats, relays,...

Product DescriptionThe HAMMOND CWAD10 is a panel adapter designed to mount a smaller subpanel or back panel inside a larger enclosure. It provides a flat, rigid mounting surface that bridges different panel sizes within an existing enclosure footprint. Electricians and enclosure integrators use this...