Devcon 11460 Epoxy Adhesive Gray 30 Lb Pail Metal

Product Description

The DEVCON 11460 is a high-density, non-sag, high-impact-resistance wearing compound designed for surface protection and metal bonding applications. Supplied as a 30-pound pail containing resin and hardener, it mixes at a 2.5:1 ratio and is applied by trowel. The cured compound delivers a shear strength of 11,500 psi and a tensile strength of 4,220 psi, making it suitable for heavily loaded metal surfaces subject to abrasion, impact, and wear. It cures to a dark gray finish with a Shore D hardness of 85 at full cure. Zero VOC content and low odor make it practical for interior and enclosed environments. Licensed trades and maintenance professionals apply it where conventional metal repair is impractical.

This compound is formulated for use on metal substrates in both interior and exterior environments, including marine-grade applications. It is suited to industrial and commercial maintenance scenarios where metal surfaces experience continuous impact or abrasion. Typical installations include pump housings, impellers, wear plates, chutes, and similar metal components. The 30-minute working time allows for placement and shaping before the material sets. Functional cure is reached in 4 to 6 hours at ambient temperature, with full cure at 16 hours. Application temperature must fall between 55 degrees F and 90 degrees F for proper adhesion and cure.

Key Features

• High-density, non-sag formula stays in place on vertical and overhead metal surfaces during application
• Shear strength of 11,500 psi and tensile strength of 4,220 psi for demanding load-bearing repairs
• 30-minute working time allows shaping and placement before cure begins
• Zero VOC content (0 g/L) and low odor rated for interior use
• Marine-grade formulation resists water and moisture exposure
• Meets multiple ASTM standards including D1002, D638, D695, and D2240

Compatibility

Designed for bonding and surface protection on metal substrates in interior and exterior settings, including marine environments. Bonds metal to metal as stated by the manufacturer.

Installation Notes

Application is performed by qualified maintenance technicians or industrial tradespeople familiar with epoxy systems. Clean and degrease the metal surface thoroughly before mixing; surface contamination is the leading cause of adhesion failure. Mix resin and hardener at the specified 2.5:1 ratio and apply by trowel within the 30-minute work life. Do not apply below 55 degrees F or above 90 degrees F, and allow full 16-hour cure before returning the assembly to service.

Technical Specifications

• Type: Non-Sag, High-Density, High-Impact-Resistance Wearing Compound
• Resin Type: Epoxy
• Mix Ratio: 2.5:1
• Total Volume: 30 lb
• Container Type: Pail
• Cured Color: Dark Gray
• Shear Strength: 11,500 psi
• Tensile Strength: 4,220 psi
• Hardness at Full Cure: 85 Shore D
• Working Time: 30 min
• Functional Cure Time: 4 to 6 hr
• Full Cure Time: 16 hr
• Minimum Application Temperature: 55 degrees F
• Maximum Application Temperature: 90 degrees F
• Maximum Performance Temperature: 300 degrees F
• Coverage: 50 sq in/lb
• Application Method: Trowel
• VOC Content: 0 g/L (0%)
• Water Resistance: Water-Resistant
• Marine Grade: Yes
• Low Odor: Yes
• Non-Sagging: Yes
• Interior/Exterior: Interior/Exterior
• Materials Bonded: Metal
• Cure Method: Ambient
• Standards: ASTM C177, ASTM D1002, ASTM D149, ASTM D150, ASTM D2240, ASTM D2566, ASTM D638, ASTM D695, ASTM D696, ASTM D790
• Weight: 19 oz

Standard Information

• Brand: DEVCON
• Manufacturer Part Number: 11460