{"product_id":"tru-maxx-szmfw13180-mounted-flap-wheel-180-grit-3in","title":"Tru-maxx SZMFW13180 Mounted Flap Wheel 180 Grit 3in","description":"\u003ch3\u003eProduct Description\u003c\/h3\u003e\n\u003cp\u003eThe TRU-MAXX SZMFW13180 is a shank-mounted flap wheel designed for surface finishing, blending, and deburring on metal and similar materials. It runs on a 1\/4-inch shank that mounts directly into a die grinder or drill press collet. The abrasive is aluminum oxide in a coated configuration rated at a very fine 180 grit, making it well suited for final-pass finishing and light stock removal. With a maximum speed rating of 20000 RPM, it keeps pace with standard pneumatic die grinders used in fabrication and maintenance shops. Machinists, tool and die workers, and metal fabricators are the typical users.\u003c\/p\u003e\n\u003cp\u003eThis flap wheel fits finishing operations where a flexible abrasive surface is needed to follow contours, reach inside bores, or blend weld seams without loading up. The 3-inch diameter and 1-inch face width provide adequate contact area for flat and curved work surfaces. At 180 grit, it is appropriate for pre-polish prep, burr removal on finished parts, and surface conditioning prior to coating or inspection. It is a single-piece unit sold individually.\u003c\/p\u003e\n\u003ch4\u003eKey Features\u003c\/h4\u003e\n\u003cul\u003e\n  \u003cli\u003e180 grit aluminum oxide coated abrasive for very fine surface finishing\u003c\/li\u003e\n  \u003cli\u003e1\/4-inch shank diameter for direct mounting in die grinders and drill chucks\u003c\/li\u003e\n  \u003cli\u003e20000 RPM maximum speed rating compatible with standard pneumatic die grinders\u003c\/li\u003e\n  \u003cli\u003e3-inch outer diameter with 1-inch face width for broad contact on flat and contoured surfaces\u003c\/li\u003e\n  \u003cli\u003eNon-interleaved flap construction for consistent, controlled cut\u003c\/li\u003e\n  \u003cli\u003eLightweight at 0.204 pounds for reduced fatigue during extended use\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eCompatibility\u003c\/h4\u003e\n\u003cp\u003eDesigned for use with die grinders, flexible shaft machines, and drill presses accepting a 1\/4-inch shank. Suitable for metal, ferrous and non-ferrous alloys, and similar hard materials requiring fine surface finishing.\u003c\/p\u003e\n\u003ch4\u003eInstallation Notes\u003c\/h4\u003e\n\u003cp\u003eA licensed machinist or experienced fabricator should verify the spindle speed of the host tool does not exceed the 20000 RPM rating before mounting. Secure the shank fully into the collet or chuck and confirm the locking mechanism is tight before operating. Always wear appropriate eye protection and follow ANSI B11 or applicable shop safety standards when operating mounted abrasives. Inspect the flap wheel for damage or loose abrasive segments before each use and remove from service if defects are found.\u003c\/p\u003e\n\u003ch4\u003eTechnical Specifications\u003c\/h4\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAbrasive Material\u003c\/strong\u003e: Aluminum Oxide\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAbrasive Type\u003c\/strong\u003e: Coated\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGrit\u003c\/strong\u003e: 180\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGrade\u003c\/strong\u003e: Very Fine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eOutside Diameter\u003c\/strong\u003e: 3 inches\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFace Width\u003c\/strong\u003e: 1 inch\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eShank Diameter\u003c\/strong\u003e: 0.25 inches\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMaximum RPM\u003c\/strong\u003e: 20000\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMount Type\u003c\/strong\u003e: Shank\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eInterleaf\u003c\/strong\u003e: No\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePackage Height\u003c\/strong\u003e: 2.25 inches\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePackage Width\u003c\/strong\u003e: 3 inches\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePackage Length\u003c\/strong\u003e: 1 inch\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e: 0.204 pounds\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eStandard Information\u003c\/h4\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBrand\u003c\/strong\u003e: TRU-MAXX\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number\u003c\/strong\u003e: SZMFW13180\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"TRU-MAXX","offers":[{"title":"Default Title","offer_id":51731262931250,"sku":"SZMFW13180","price":14.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0270\/4519\/9983\/files\/12b07b981ec1a6e9ac6632eabdafa271.jpg?v=1788728948","url":"https:\/\/voomisupply.com\/products\/tru-maxx-szmfw13180-mounted-flap-wheel-180-grit-3in","provider":"Voomi Supply","version":"1.0","type":"link"}