{"product_id":"mueller-streamline-absbend14112-abs-dwv-vent-elbow","title":"Mueller Streamline ABSBEND14112 Abs Dwv Vent Elbow","description":"\u003ch3\u003eProduct Description\u003c\/h3\u003e\n\u003cp\u003eThe MUELLER STREAMLINE ABSBEND14112 is a 90-degree ABS DWV vent elbow designed for use in the venting side of drain, waste, and vent (DWV) plumbing systems. The hub x hub end connections accept pipe on both ends for a secure solvent-weld joint. The abrupt 90-degree angle redirects airflow within the vent stack rather than carrying liquid waste. This fitting is rated for service temperatures from -40 degrees F to 180 degrees F and meets ASTM D2665, ASTM D3965, ASTM D2661, ASTM D3311, and NSF\/ANSI Standard 14. It carries a UL Listed 94V-0 rating and NSF U.P. Certification. Licensed plumbers and pipefitters typically install this fitting in residential and light commercial DWV rough-in work.\u003c\/p\u003e\n\u003cp\u003eThis elbow is used in 1-1\/2 inch ABS vent piping runs where a sharp directional change is required on the vent side of the system. Common install scenarios include vent stack offsets, through-wall vent routing, and tie-ins at the top of fixture drain assemblies. Because this is a vent elbow with an abrupt bend geometry, it is not intended for use on the drainage side of the system where a long-sweep elbow would be required by code. It is sourced domestically and belongs to the Series 5807-V product line.\u003c\/p\u003e\n\u003ch4\u003eKey Features\u003c\/h4\u003e\n\u003cul\u003e\n  \u003cli\u003e90-degree abrupt bend geometry for vent-side direction changes in ABS DWV systems\u003c\/li\u003e\n  \u003cli\u003eHub x hub connection on both ends for solvent-weld installation\u003c\/li\u003e\n  \u003cli\u003eABS material rated for service temperatures from -40 degrees F to 180 degrees F\u003c\/li\u003e\n  \u003cli\u003eMeets ASTM D2665, ASTM D3965, ASTM D2661, and ASTM D3311 standards\u003c\/li\u003e\n  \u003cli\u003eNSF\/ANSI Standard 14 and NSF U.P. Certified\u003c\/li\u003e\n  \u003cli\u003eUL Listed 94V-0 flame rating\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eCompatibility\u003c\/h4\u003e\n\u003cp\u003eDesigned as an OEM-style replacement or new-installation fitting for 1-1\/2 inch ABS DWV vent piping in residential and light commercial plumbing systems. Not for use on the drain or waste side of the system where long-sweep fittings are required.\u003c\/p\u003e\n\u003ch4\u003eInstallation Notes\u003c\/h4\u003e\n\u003cp\u003eInstallation should be performed by a licensed plumber in accordance with the International Plumbing Code (IPC) and applicable local codes. Use only ABS solvent cement rated for ABS-to-ABS joints and allow full cure time before system testing. Do not test or use this fitting with compressed air or any other gas. Shut off the water supply and verify zero pressure in the affected line before beginning any fitting work.\u003c\/p\u003e\n\u003ch4\u003eTechnical Specifications\u003c\/h4\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eNominal Size\u003c\/strong\u003e: 1-1\/2 inches\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMaterial\u003c\/strong\u003e: ABS\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eEnd Style\u003c\/strong\u003e: Hub x Hub\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting Type\u003c\/strong\u003e: 90 Degree Elbow\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eTemperature Rating\u003c\/strong\u003e: -40 degrees F to 180 degrees F\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSeries\u003c\/strong\u003e: 5807-V\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eStandards\u003c\/strong\u003e: ASTM D2665, ASTM D3965, ASTM D2661, ASTM D3311, NSF\/ANSI Standard 14\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertifications\u003c\/strong\u003e: UL Listed 94V-0, NSF U.P. Certified\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCountry of Origin\u003c\/strong\u003e: Domestic\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eStandard Information\u003c\/h4\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBrand\u003c\/strong\u003e: MUELLER STREAMLINE\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number\u003c\/strong\u003e: ABSBEND14112\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"MUELLER STREAMLINE","offers":[{"title":"Default Title","offer_id":68104350564658,"sku":"ABSBEND14112","price":14.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0270\/4519\/9983\/files\/f83d3258174ae3be865bbd757da02c4b.jpg?v=1793316161","url":"https:\/\/voomisupply.com\/products\/mueller-streamline-absbend14112-abs-dwv-vent-elbow","provider":"Voomi Supply","version":"1.0","type":"link"}