{"product_id":"boneham-h325hg-press-fit-headed-drill-bushing-steel","title":"Boneham H325HG Press Fit Headed Drill Bushing Steel","description":"\u003ch3\u003eProduct Description\u003c\/h3\u003e\u003cp\u003eThe BONEHAM H325HG is a Type H press fit headed drill bushing manufactured from hardened steel for use in jig and fixture applications. It features a 0.250 inch inside diameter (Letter E), a 0.500 inch body outside diameter, and a 5\/16 inch length under the head. The head outside diameter measures 39\/64 inch and the head height is 7\/32 inch. Hardness runs 60 to 65 HRC, and the inside diameter tolerance is held to +0.0001 to +0.0004 inch, providing precise drill guidance and repeatable hole location. Machinists, tool and die makers, and production fixture builders install this bushing to control drill, reamer, or boring tool alignment across repeated operations.\u003c\/p\u003e\u003cp\u003eThis bushing is suited for permanent press fit installation in drill jigs used in metalworking, fabrication, and general machining environments. Because it is not a renewable-type bushing, it is intended for fixed, high-volume applications where the same tool size is used throughout the run. The headed configuration seats flush against the jig plate face, preventing the bushing from being driven through the jig under thrust loads. ANSI standards govern its dimensions, making it interchangeable with other ANSI-conforming Type H bushings of the same ID and OD.\u003c\/p\u003e\u003ch4\u003eKey Features\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003ePress fit installation — no locking screws or removal notches required\u003c\/li\u003e\n\u003cli\u003eHeaded (Type H) design resists axial push-through under drilling thrust\u003c\/li\u003e\n\u003cli\u003e0.250 inch bore with +0.0001 to +0.0004 inch tolerance for tight drill guidance\u003c\/li\u003e\n\u003cli\u003e60 to 65 HRC hardness resists wear from repeated tool contact\u003c\/li\u003e\n\u003cli\u003eANSI-dimensioned for interchangeability with standard Type H drill bushing tooling\u003c\/li\u003e\n\u003cli\u003eNon-renewable design for permanent, dedicated-tool-size fixture installations\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eCompatibility\u003c\/h4\u003e\u003cp\u003eDesigned as an ANSI-standard Type H press fit headed drill bushing for use in drill jigs and machining fixtures requiring a 0.250 inch inside diameter and 0.500 inch body outside diameter.\u003c\/p\u003e\u003ch4\u003eInstallation Notes\u003c\/h4\u003e\u003cp\u003eInstallation is performed by machinists or toolmakers using a press or arbor press to seat the bushing into a properly reamed jig plate hole. The mating hole in the jig plate must be reamed to the specified interference fit dimension for the 0.500 inch OD before pressing. Never drive the bushing with a hammer directly on the head face, as this can distort the bore. Because this is a permanent press fit bushing, plan tool-size requirements before installation, as removal typically damages the bushing or the jig plate.\u003c\/p\u003e\u003ch4\u003eTechnical Specifications\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInside Diameter\u003c\/strong\u003e: 0.250 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInside Diameter Letter\u003c\/strong\u003e: E\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInside Diameter Tolerance\u003c\/strong\u003e: +0.0001 to +0.0004 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBody Outside Diameter\u003c\/strong\u003e: 0.500 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead Outside Diameter\u003c\/strong\u003e: 39\/64 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead Height\u003c\/strong\u003e: 7\/32 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength Under Head\u003c\/strong\u003e: 5\/16 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation Method\u003c\/strong\u003e: Press Fit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBushing Industry Code\u003c\/strong\u003e: H\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead Configuration\u003c\/strong\u003e: Headed\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRenewable\u003c\/strong\u003e: No\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCounterbored\u003c\/strong\u003e: No\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial\u003c\/strong\u003e: Steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardness\u003c\/strong\u003e: 60 to 65 HRC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStandards\u003c\/strong\u003e: ANSI\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eStandard Information\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand\u003c\/strong\u003e: BONEHAM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number\u003c\/strong\u003e: H325HG\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"BONEHAM","offers":[{"title":"Default Title","offer_id":51738145194290,"sku":"H325HG","price":18.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0270\/4519\/9983\/files\/7a3df753bfacdecf7a1650e3bb823de6_ef79181a-2fa8-45c7-831a-f45e70c84835.jpg?v=1788796425","url":"https:\/\/voomisupply.com\/products\/boneham-h325hg-press-fit-headed-drill-bushing-steel","provider":"Voomi Supply","version":"1.0","type":"link"}